Revival Defense & Forward Controls Design
6315RF LH 5.56 Flash Hider & 1x16LH Suppressor Mount
The 6315RF LH is an A2 style closed bottom flash hider & 1x16LH Suppressor Mount. The "LH" series of our RF devices are compatible with 1x16LH suppressors and HUB mounts, including but not limited to offerings from CAT, CGS, Cobalt Kinetics, and any HUB compatible suppressor via a 1x16LH HUB mount such as the CAT TSFX.
ABOUT THE RF SERIES MUZZLE DEVICES
The RF Series Muzzle Devices were designed to be compact yet effective standalone muzzle devices which also serve as a rugged and reliable suppressor mount that doesn’t add unnecessary weight or length to the front of your rifle. We set out to design a practical device for end users who want a no frills, high performance standalone device that they can securely attach their suppressor to.
The RF series muzzle devices were designed in collaboration between and Revival Defense and Forward Controls Design
Features
- Flash Hider - Like all of our RF devices, we focus on the function of the device in all aspects to create effective and cartridge optimized standalone muzzle devices
- 1x16LH Suppressor Mount - Our “LH” devices feature a 1x16LH Suppressor mount, compatible with Silencers that feature the integral 1x16LH mounting system such as the CAT QD Silencers, CGS SCI SIX, Cobalt Scrambler QD and also adaptable to HUB silencers using mounts such as the CAT TSFX and AI HUB QD, Available HERE
- Closed Bottom - The 6315RF LH features a closed bottom, similar to the traditional A2 Birdcage flash hider, which prevents dust and debris from being kicked up and disrupting your sight picture when shooting from a prone position. The closed bottom also slightly aids in recoil mitigation.
- Standard Wrench Flats - All of our RF devices feature standard 3/4” wrench flats, the same flat size found on millions of Armorer’s wrenches and on the DPW and JMW wrench for ease of installation with common tools
- Nitride Finish - The nitride process greatly increases the surface hardness of the muzzle device while lending itself to a tighter seal in the suppressor itself
What’s Included
1x 6315RF LH Muzzle Device
1x Rocksett Packet
Specifications
- Length: 1.755”
- Weight: 2.45oz
- Thread Pitch: 1/2x28
- Cartridge Compatibility: .223 / 5.56
- Suppressor Compatibility: 1x16LH
- Material: 17-4 PH H900
- Nitride Finish
- Wrench Flats: 3/4”
Installation
- Ensure firearm is unloaded
- Clean surfaces of debris
- Test fit muzzle device with alignment shims
- Install muzzle device with shims & a small amount of Rocksett
- Torque to 25+/-5ft-lb
The 6315RF requires timing. Allow Rocksett to cure for at least 12 hours before use. Make sure to check alignment with your suppressor before use.
FAQ
Q: Is the 6315RF long enough to be Pinned and Welded?
Yes and No. Anything “can” be pinned and welded, but you would need an approximately ~15.1” barrel to comfortably bring this device over the 16” length that most folks are aiming to achieve with a pinned and welded device. So why is there a blind hole? The reason the blind hole is there is simply because it added no cost and virtually no additional time in the manufacturing process to add to the devices with no downsides in performance or durability while offering more options to our customers and opens up the ability for manufacturers to proliferate more firearms without having to subject their rifles to unconstitutional NFA laws.
Q: Can I use the 6315RF on a 9mm?
NO. The 6315RF was designed around the 5.56/.223 cartridge and the bore will not fit a 9mm.
*Only use the wrench flats for installation of your muzzle device. Do not use a screwdriver or any other tool to apply torque through the ports. The DPW is specifically designed for installation of suppressor mounts and available HERE *Use on Q Cans will void your warranty
Shop other RD Products
[ITEMPRICE]