Revival Defense & Forward Controls Design
6315RF-A1 5.56 Flash Hider & Plan B Suppressor Mount - 1/2x28
The 6315RF-A1 (Revival Defense, Forward Controls) is an A1 style, omni directional ported flash hider. The RF series muzzle devices were designed in collaboration between Forward Controls Design and Revival Defense
Will this fit my suppressor? Suppressor Mount Compatibility Chart
The 6315RF-A1 is the same OAL as our 6315RF in regards to compatibility
Features
- Flash Hider - Like all of our RF devices, we focus on the function of the device in all aspects to create effective and cartridge optimized standalone muzzle devices
- Suppressor Mount - Plan B Compatible - for use with Plan B style mounts such as our Atlas R and Rearden Atlas, along with any other Plan B compatible mounts.
- Omni Directional Porting - Unlike our standard 6315RF which is similar to an A2 with a closed bottom, the 6315RF-A1 features 360 degree porting providing slightly better flash performance, allows for even dispersion of gasses in all directions and does not requiring timing during installation
- Standard Wrench Flats - All of our RF devices feature standard 3/4” wrench flats, the same flat size found on millions of Armorer’s wrenches and on the DPW and JMW wrench for ease of installation with common tools
- Nitride Finish - The nitride process greatly increases the surface hardness of the muzzle device while lending itself to a tighter seal in the suppressor itself
What’s Included
1x 6315RF-A1 Muzzle Device
1x Rocksett Packet
Specifications
- Length: 1.725”
- Weight: 2.0oz
- Thread Pitch: 1/2x28
- Suppressor Compatibility: Rearden Atlas and Plan B Mounts
- Material: 17-4 PH
- Nitride Finish
- Wrench Flats: 3/4”
Installation
- Ensure firearm is unloaded
- Clean surfaces of debris
- Test fit muzzle device
- Install muzzle device with shims & a small amount of Rocksett
- Torque to 25+/-5ft-lb
The 6315RF-A1 does not require timing. Allow Rocksett to cure for at least 12 hours before use. Make sure to check alignment with your suppressor before use.
FAQ
Q: Is the 6315RF long enough to be Pinned and Welded?
Yes and No. Anything “can” be pinned and welded, but you would need an approximately ~15.1” barrel to comfortably bring this device over the 16” length that most folks are aiming to achieve with a pinned and welded device. So why is there a blind hole? The reason the blind hole is there is simply because it added no cost and virtually no additional time in the manufacturing process to add to the devices with no downsides in performance or durability while offering more options to our customers and opens up the ability for manufacturers to proliferate more firearms without having to subject their rifles to unconstitutional NFA laws.
Q: Can I use the 6315RF-A1 on a 9mm?
NO. The 6315RF was designed around the 5.56/.223 cartridge and the bore will not fit a 9mm. Our friends over at Rearden Manufacturing offer muzzle devices in large bore variations that can safely fit a 9mm cartridge.
Q: What Suppressors can I use this with?
The options are virtually endless, as long as the suppressor features a “HUB” 1.375x24 threaded rear end, you can install our Atlas-R or Rearden Atlas and use the RF Muzzle devices. Fitment varies between silencers, so we put together this compatibility chart: https://www.revivaldefense.com/rdsmcc to make things a bit easier!
*Only use the wrench flats for installation of your muzzle device. Do not use a screwdriver or any other tool to apply torque through the ports. The DPW is specifically designed for installation of suppressor mounts and available HERE
*Use on Q Cans will void your warranty
Shop other RF Series Muzzle Devices
[ITEMPRICE]