Revival Defense & Forward Controls Design
1215RF 5.56 Muzzle Brake & Plan B Suppressor Mount - 1/2x28
The 1215RF (Revival Defense, Forward Controls) is a Single Port Muzzle Brake and Plan B / Rearden Atlas Compatible Silencer Mount Threaded in 1/2x28 designed in collaboration between Forward Controls Design and Revival Defense
ABOUT THE RF SERIES MUZZLE DEVICES
The RF (Revival Defense, Forward Controls) Muzzle Devices were designed to be compact, yet practical and effective standalone muzzle devices which also serve as a reliable suppressor mount that doesn’t add unnecessary weight or length to the front of your rifle.
Features
Single Chamber Muzzle Brake
Muzzle Brakes can greatly reduce felt recoil, aiding in quicker follow up shots and better target tracking, but this does not come without a cost. Muzzle brakes greatly increase the report of the gun shot along with the flash signature, which is why as a standalone device we typically lean towards a flash hider. However, muzzle brakes act as a sacrificial first baffle, so for those using a suppressor they may be more appealing, especially on a setup that is going to almost always have a suppressor on it.
Plan B & Rearden Atlas Compatible Suppressor Mount
Our RF Series of Muzzle Devices feature a suppressor mount compatible with Rearden Atlas and Plan B Type Mounts. This suppressor mounting system utilizes a taper and threads to ensure a proper seal that is repeatable and reliable without adding unnecessary weight or length to the system.
Nitride Finish
The Nitriding process greatly increases the surface hardness of the muzzle device while lending itself to a tighter seal in the suppressor itself.
Standardized Wrench Flats
RF Series Muzzle Devices Feature 3/4” Wrench Flats for ease of installation. The FCD JMW, Armorers Wrench or any other 3/4" Wrench can be used for installation
What’s Included
1x 1215RF Muzzle Device
1x Rocksett Packet
Specifications
Installation
The 1215RF must be timed. The Cygnus and RD logo should be at the bottom with the unengraved side facing top dead center when properly installed. Allow Rocksett to cure for at least 12 hours before use. Make sure to check alignment with your suppressor and that your device is properly installed before use.
FAQ
Q: Is the 1215RF long enough to be Pinned and Welded?
Yes and No. Anything “can” be pinned and welded, but you would need an approximately ~15.1” barrel to comfortably bring this device over the 16” length that most folks are aiming to achieve with a pinned and welded device. So why is there a blind hole? The reason the blind hole is there is simply because it added no cost and virtually no additional time in the manufacturing process to add to the devices with no downsides in performance or durability while offering more options to our customers.
Q: What Suppressors can I use this with?
The options are virtually endless, as long as the suppressor features a “HUB” 1.375x24 threaded rear end, you can install our Atlas-R or Rearden Atlas and use the RF Muzzle devices. Fitment varies between silencers, so we put together this compatibility chart: https://www.revivaldefense.com/rdsmcc to make things a bit easier!
Q: Should I buy a muzzle brake if I plan to primarily shoot suppressed?
“... the user is encouraged to consider their use case(s) when selecting a direct-thread silencer or a muzzle brake mounted silencer, as muzzle brake mounts ... can serve as “sacrificial” blast baffles on certain host weapons such as short-barrel semi-automatic rifles.” - Jay, Pew Science 2022, Dec 11 SSS.6.99
It’s really up to you. It will reduce erosion in the blast chamber over time, but with modern, quality suppressors built for durability, even on shorter barrel rifles that generate extreme amounts of pressure at the muzzle, we’re typically talking tens of thousands of rounds that most suppressors will last, that’s multiple barrels and likely tens of thousands of dollars in ammunition in today's world before these things start to show extreme wear. Most suppressor manufacturers understand that most of us don’t want to purchase an item, wait hundreds of days for an unconstitutional waiting period and end up with a suppressor that might only last a year or two of serious usage on a common platform. That being said, we like to consider all factors with our muzzle device choices; what do you want the device to do as a standalone device primarily. If you don’t care about what the muzzle device does like hiding the flash when you do not have a suppressor attached, then we would go with a muzzle brake. If you want a device that mitigates flash and concussion, our 6315RF and 6310RF are available HERE. If you want a dedicated flash hider, our 3P15 is available HERE. While the erosion is a consideration, it absolutely would not sway our decision past the performance of the device on its own. Purchase based on what you want the device to do, and your individual use case.
Q: Can I use the 1215RF on a 9mm?
NO. The 1215RF was designed around the 5.56/.223 cartridge and the bore will not fit a 9mm. Some of the muzzle devices from our friends at Rearden Manufacturing offer muzzle devices in large bore variations that can safely fit a 9mm cartridge.
*Only use the wrench flats for installation of your muzzle device. Do not use a screwdriver or any other tool to apply torque through the ports. The FCD JMW is specifically designed for installation of suppressor mounts and available HERE
*Use on Q Cans will void your warranty
Shop other RF Series Muzzle Devices
[ITEMPRICE]